====== 3D-Printed Automatic Weather Station (3D PAWS) ======

==== Links ====
  * [[https://sites.google.com/ucar.edu/3dpaws/home|NCAR 3D-PAWS Web Site]]
  * [[http://3d.chordsrt.com/dashboard|CHORDS live data Website]]


==== Projects ====
  * [[atmos:3d-paws:VisibilitySensor|Visibility Sensor]]

==== Current Stations ====
  *[[atmos:3d-paws:und00100|UND 00100]]
  *[[atmos:3d-paws:und00200|UND 00200]]
  *[[atmos:3d-paws:und00300|UND 00300]]
  *[[atmos:3d-paws:und00400|UND 00400]]

==== Hardware 3D-PAWS ====
  * There is no drop ceiling clamp available.
  * Sensor Sub-Assembly 4 is confusing, Need to put male jumper on female to make male-to-male.
  * The small square magnetic comes with the sensor.
  * Current printer filament: Overture PLA 1.75mm
  * Current Printer: [[atmos:3dprinter:Huafast HS]]
  * Current Printer Location: Clifford 601
  * Current slicer: Ultimaker Cura


==== Software - SD Cards ====
  * Command to write image to SD card on Linux, where /dev/mmcblk0 is the device of the card on the system.
    * sudo dd if=./3dpaws_pi.img of=/dev/mmcblk0
  * Command to read image SD card on Linux, where /dev/mmcblk0 is the device of the card on the system.
    * sudo dd if=/dev/mmcblk0 of=./3dpaws_pi.img
  * Label the SD Cards with Current Station serial number and software date
    * Example: UND# # # # # & YYYYMMDD (no spaces between #'s)

==== Software - Rassberry Pi Configuration ====
  * Within terminal navigate to find Host Name
    * cd /etc
    * sudo vi hostname
    * Host name will be 3D-PAWS serial number and software date
      * Example: UND# # # # #-YYYYMMDD (no spaces between #'s)
    * To save enter ->  :w
    * Then hit enter and save as usual
  * Navigate to Hosts to set the IP address 
    * cd /etc
    * sudo vi hosts
    * Hosts is localhost IP address
  * Communicate with 3D-PAWS by installing TeamViewer software
    * Rename "Your Display Name"
      * Name will be:  UND# # # # #-YYYYMMDD
    * Assign to Account: for now we are using David Delene's account
    * Security
      * Change Password to our standard password: sudo su; passwd pi 
    * ID Number: enter into GoogleDocs

==== Software - Raspberry Pi Setup ====
  * To setup/change software for new stations:
    * On the Desktop, click the 3D-PAWS icon
    * Settings
    * CHORDS menu 
    * Set 3D-PAWS ID to the correct number
      * Found on CHORDS site
    * Set web address
      * Replace 3d.chordsrt.com with CHORDS IP address 
        * Example: #.# #.# #.# #.com (no spaces between #'s)


==== Tar File ====
 {{ :atmos:3d-paws:3d_paws_scripts.tar |3d_paws Scripts Tar File}}

==== Current Problems and Possible Solutions ====
| High winds on roof blow over rain gauge        | cement PVC fitting connection in place, more leg supports? |
| Internet connectivity                          | Run a Ethernet cable out from room 601 to roof             |

==== Digital Key Numbers ==== 
| Sensor (Honeywell SS451A bipolar Hall Effects) | DIGI-Key P/N 480-3587-ND   |
| Capacitor (0.1 microfarad)                     | DIGI-Key P/N 399-4454-1-ND |
| 1K ohm Resistor                                | DIGI-Key P/N 1.00KXBK-ND   |
| 360 Deg Rotary Sensor                          | DIGI-Key P/N 55300-00-02-A | 
| Analog to Digital IC                           | DIGI-Key P/N C410C104M5U5TA7200|

==== Adafruit Sensors and links ====
| BMP280 Pressure & Altitude Sensor              |[[https://www.adafruit.com/product/2651]]|
| HTU21D-F Temperature & Humidity Sensor         |[[https://www.adafruit.com/product/1899]]|
| MCP9808 I2C Temperature Sensor                 |[[https://www.adafruit.com/product/1782]]|
| SI1145 Digital UV Index/IR/Visible Light Sensor|[[https://www.adafruit.com/product/1777]]|


[[http://wiki.atmos.und.edu/doku.php?id=atmos:home|Back]]