Differences

This shows you the differences between two versions of the page.

--- atmos:researchmeetingnotes:researchmeetingnotes:home:ryan_kucera [2020/12/10 19:10] – delene
+++ atmos:researchmeetingnotes:researchmeetingnotes:home:ryan_kucera [2021/04/21 18:09] (current) – delene
@@ Line 231: / Line 231: @@
 No meeting next week or later, After break talk to figure out.
+===== January 20, 2021 =====
+Attending: Ryan Kucera, David Delene
+=== Tasks ====
+  * Check Box box for sensor and SD cards.
+  * Email link with sensors in radiation shield and radiation sensor.  Get more.
+  * Find out sensor we need for next version of software to work.
+Meet on Sunday and again next week.
+===== January 27, 2021 =====
+Attending: Ryan Kucera, David Delene, Marwa Majdi
+==== Discussion ====
+ * Need SD Cards, on order, get one for Sunday.
+ * Need PVC pile, 1 inch.  At least 1 8 ft section for one.
+=== Tasks ====
+ * Ryan send link for 5 way tee.
+See you on Sunday, Meet next week at Wednesday.
+===== February 3, 2021 =====
+Attending: Ryan Kucera, David Delene
+==== Discussion ====
+ * Seem that bending SD cards messy them up.
+ * Try to write image on Friday, got latest version.  Should have 5 additional cards.
+ * Get 3d-PAWS for Nathan. Emailed Shawn to see about getting him to help.
+===== February 10, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+  * Talked about the pressure sensor setup and issues. Should get new video cables.
+  * Can use the one cable so far.
+  * Need order 6 digital Wind sensors.
+  * Need box sometime for shipping.
+==== Tasks ====
+  * Need PVC Pipe, 1 inch. Need one or two 8 ft sections.
+Talk next week at this time.  Will be in on Sunday.
+===== February 17, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+  * Ryan wrote images to SD cards on Sunday.
+  * Requested two additional mouse/keyboards for the Raspberry PIs.
+  * Got Cable in box and together, waiting to test after drying.
+  * Update old 3D-PAWS with new wind sensor, really not needed.
+==== Tasks ====
+  * David - Sent CS125 manual to Ryan.
+===== March 3, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+  * Burn lab version of new 3d-paws software to SD card for Pi on wooden bench in CH423 used for pressure lab. Test out and see pressure display/file working at 1 second.
+  * Latest Teamviewer should work.  Will try on Pressure Pi in 423.
+  * The Wind speed and prec. don't come back like the other measurements or drop off.  Find after a reboot.
+  * Don't forget about visibility sensor.
+  * Look for tee in CH430, let if don't have.
+==== Tasks ====
+  * Ryan - Create Lab SD version.  Test on CH423 system.
+  * David - order 3 pis with 6 SD cards, 32 GB, get some cases.
+  * Ryan - Power cycle the SN00200 see if Wind speed and prec. come back. If so, email NCAR with this observation.
+Try to come in Sunday.  Talk next week on Wednesday.
+===== March 10, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+ * Sending out 3D-PAWS, elbow 90 degrees, PVC 1"
+ * New images should work with old wind sensors. 3D-PAWS 200 on metTrailer, and using a new 3D-PAWS 3B for SN00100.  Just change the Id in the input.txt.
+  * Should be normal menu.  Try using windows key on keyboard.
+  * Should have every things.  Get some things for the initial test station.
+  * Please come by at 5 tomorrow, Sunday SN00200 take down.
+Next time, Wednesday.
+===== March 24, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+ * Have to test new image.
+ * Have 10 more, order 25 or 50 more elbes.
+ * Get thick 1 inch tube, thicker stuff.
+ * Design smaller rain gauge funnel (3 " instead of 6).  Cut top vertical section in half. For better shipping.
+Talk next week.
+===== March 24, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+ * Filament to use for 3D-PAWS. Order https://www.amazon.com/Polymaker-Printer-Filament-PolyLite-Printing/dp/B07QM79N45/ref=sr_1_3?dchild=1&keywords=polymaker+asa+1.75&qid=1617214065&sr=8-3, in stock on April 6.
+ * Fixed cable for SN00300.
+ * Would on new direction sensor. Need new cables for the wind direction.
+ * David need to work on weather line for the 3D-PAWS.
+ * Build not open on Monday since holiday.
+Sunday Easter, no lab work. Maybe Monday.
+===== April 14, 2021 =====
+Attending: Ryan Kucera, David Delene
+===== Discussion =====
+ * Will picked up filament today in lab.
+ * Working on building 4 digital wind direction. Friday afternoon, will pick on Friday afternoon. Need cables for the 300.
+ * Have new covers for 3D-PAWS
+ * David Singewald will help with visibility sensor.
+ * Internet access CH601 , wireless ports in CH601, see 3d-paws works on UND-secure.
+Likely come in on Sunday. Chat again to catch.
+===== April 21, 2021 =====
+Attending:  Ryan, David Delene
+==== Discussion ====
+  * Working on printing stuff.
+  * Change Key, need to get new one.
+  * Work until end of May.
+  * I'll Met Cable.
+    * SN00300 new cable need to test.
+Catch up next week.
+* Maybe for Sunday.